Question for fellow EZM 1.1 Owners

Discussion of Sinn watches.
Post Reply
User avatar
bpax
Posts: 1444
Joined: Sat Oct 16, 2010 7:37 am
Name: Bill
Location: Fort Worth, Texas

Question for fellow EZM 1.1 Owners

Post by bpax » Sat Mar 17, 2018 2:23 pm

I'm a bit thick in the skull and cannot for the life of me figure out how to remove the bracelet.

I've broken the tip off a spring bar tool trying to get the damn thing off and was wondering if any of you have any suggestions, tips, etc.

Granted, I may have had a few pops while trying to take the thing off, but I'm fairly certain the bourbon is not the cause of my problem.

Many thanks in advance.

User avatar
hoppyjr
HJ
Posts: 29408
Joined: Thu Feb 24, 2011 9:05 am
Name: Hoppy
Location: Washington State

Question for fellow EZM 1.1 Owners

Post by hoppyjr » Sat Mar 17, 2018 2:43 pm

I do it the same as any other watch; hold in your hand face down, use a finger or two to put upward pressure on the end link while simultaneously releasing one end of the spring bar on that lug, keep the upward pressure on the end link so it doesn’t slip back in, then release the other end of spring bar and press up (toward the caseback) to remove.

Edit: finger not ringer.
Last edited by hoppyjr on Sat Mar 17, 2018 2:43 pm, edited 1 time in total.

User avatar
bpax
Posts: 1444
Joined: Sat Oct 16, 2010 7:37 am
Name: Bill
Location: Fort Worth, Texas

Re: Question for fellow EZM 1.1 Owners

Post by bpax » Sat Mar 17, 2018 3:28 pm

hoppyjr wrote:
Sat Mar 17, 2018 2:42 pm
I do it the same as any other watch; hold in your hand face down, use a ringer or two to put upward pressure on the end link while simultaneously releasing one end of the spring bar on that lug, keep the upward pressure on the end link so it doesn’t slip back in, then release the other end of spring bar and press up (toward the caseback) to remove.
Thanks. I figure it's user error more than anything.

User avatar
Nellipj
Posts: 4705
Joined: Mon Dec 17, 2012 4:56 am
Name: Patrick
Location: Frankfort, IL

Re: Question for fellow EZM 1.1 Owners

Post by Nellipj » Sat Mar 17, 2018 4:58 pm

It is one of the more difficult ones to remove. The tolerance is very tight for the endlinks. The Sinn rubber was even more difficult on the 1.1 for me.

User avatar
aikiman44
Tiki Extraordinaire
Posts: 7062
Joined: Fri Dec 04, 2009 7:50 am
Name: Dr Jay
Location: Long Island, NY

Re: Question for fellow EZM 1.1 Owners

Post by aikiman44 » Sat Mar 17, 2018 5:32 pm

I had the bracelet on but have been unsuccessful in attaching the rubber.
"We'd better synchronize our watches."

User avatar
hoppyjr
HJ
Posts: 29408
Joined: Thu Feb 24, 2011 9:05 am
Name: Hoppy
Location: Washington State

Re: Question for fellow EZM 1.1 Owners

Post by hoppyjr » Sat Mar 17, 2018 5:55 pm

aikiman44 wrote:I had the bracelet on but have been unsuccessful in attaching the rubber.
You just roll it on.

Image

User avatar
bpax
Posts: 1444
Joined: Sat Oct 16, 2010 7:37 am
Name: Bill
Location: Fort Worth, Texas

Re: Question for fellow EZM 1.1 Owners

Post by bpax » Sat Mar 17, 2018 6:10 pm

hoppyjr wrote:
Sat Mar 17, 2018 5:55 pm
aikiman44 wrote:I had the bracelet on but have been unsuccessful in attaching the rubber.
You just roll it on.

Image
:roll: :roll: :roll:

User avatar
aikiman44
Tiki Extraordinaire
Posts: 7062
Joined: Fri Dec 04, 2009 7:50 am
Name: Dr Jay
Location: Long Island, NY

Re: Question for fellow EZM 1.1 Owners

Post by aikiman44 » Sat Mar 17, 2018 7:00 pm

Some girl I grew up with demonstrated proper condom application using a banana on a tv talk show years ago.
"We'd better synchronize our watches."

Post Reply

Who is online

Users browsing this forum: No registered users and 4 guests